Moto G7 Optimo Maxx Screen Replacement

Introduction

Utilize this guide to remove or replace the screen on your Motorola Moto G7 Power.

This procedure requires removing the glued in battery. Do not reuse the battery after it has been removed. Exist certain to supervene upon the old bombardment, equally reusing information technology tin can create a potential safety hazard.

Some images may have visual discrepancies, such as the SIM carte tray being removed from the telephone. You don't need to remove the SIM carte du jour tray for this procedure.

You'll need some double-sided tape (such as Tesa record) in order to adhere the replaced components.

For your safety, discharge the bombardment below 25% earlier disassembling your phone. This reduces the risk of a dangerous thermal event if the battery is accidentally damaged during the repair. If your bombardment is swollen, take appropriate precautions.

• Apply a heated iOpener or a oestrus gun to the bottom edge of the screen for approximately two minutes to help soften the agglutinative.

• A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device—the display and internal battery are both susceptible to heat damage.



• Apply a suction loving cup to the rear cover, as shut to the heated border as possible.

• Pull up on the suction loving cup with strong, steady force to create a gap.

• Depending on the age of your device, this may exist difficult. If you take trouble, apply more heat and try over again.

• Insert an opening pick into the gap you lot created nether the rear encompass.

• Slide the pick along the bottom of the gap to slice through the adhesive securing the rear comprehend to the midframe.

• After being cutting, the adhesive will sometimes stick back together as information technology cools. To prevent this, you can leave the pick in this edge after cutting, and continue the next steps with a new pick. Repeat this with each border, leaving a pick and standing with a new i.

• Slide the pick along the gap on the same side of the phone as the SIM carte du jour tray to slice through the adhesive securing the rear cover to the midframe.

• Slide the pick along the gap at the acme of the phone to slice through the adhesive securing the rear cover to the midframe.

• Slightly elevator upwards the rear cover starting from the right side.

• This will prevent harm to the fingerprint sensor connector under the left side of the rear cover.

• If lifting the rear encompass is difficult, slice through any remaining adhesive with an opening pick. Reapplying the iOpener can likewise help weaken the agglutinative.

• Use a finger to press down on the fingerprint sensor until it separates from the rear cover.

• Remove the rear comprehend, taking care non to impairment the fingerprint sensor.

• During reassembly, follow this guide to install custom-cut adhesives for your device.

• Insert the pointed finish of a spudger into the divot at the acme of the fingerprint sensor connector cover.

• Gently pry the cover open up.

• Remove the cover.

• Use the pointed stop of a spudger to pry up on the fingerprint sensor connector to disconnect it.

• Use a T5 Torx screwdriver to remove the ten screws securing the motherboard cover to the midframe:

• Nine three.5 mm screws

• 1 3.0 mm spiral

• Insert the flat end of a spudger nether the motherboard embrace.

• Pry the motherboard comprehend upwards to lift it from the motherboard.

• Remove the motherboard comprehend.

• Apply the flat cease of a spudger to pry up on the bombardment connector to disconnect information technology.

• If you lot are using agglutinative remover, follow these preparation steps first.

• Use ii-3 drops of loftier concentration (over xc%) isopropyl alcohol under each corner of the battery and allow it to penetrate for several minutes to help weaken the adhesive.

• Insert an opening pick into the minor gap between the battery and its compartment.

• Take intendance not to puncture or bend the battery with your tool—a punctured or aptitude battery may leak unsafe chemicals or cause a thermal event.

• Remove the opening pick and insert it into the minor gap on the other side of the bombardment. This will jiggle the bombardment effectually in its compartment, further weakening the adhesive under the battery.

• Repeat the process until you tin easily insert the choice into both gaps.

• If this pace feels difficult, apply more than isopropyl booze, wait, and endeavor again.

• Insert a option into the gap to the left of the battery and slide its tip underneath the battery.

• Both the screen connector and interconnect cablevision are located underneath the battery. Be careful non to damage them while using the opening choice!

• Slide the selection forth the left side of the battery to piece through the adhesive securing it to the midframe.

• Once the left side of the bombardment begins to separate from the midframe, leave an opening pick in the gap to keep the battery slightly raised.

• Utilize iv to five drops of isopropyl alcohol directly to the adhesive securing the bombardment to the midframe.

• Repeat the previous stride until you lot've sliced through most of the adhesive.

• If y'all are having trouble reaching the adhesive under the right side of the battery, utilize a longer opening tool like a plastic carte to slice through whatsoever remaining agglutinative without bending or puncturing the battery.

• Use an opening pick to gently pry the battery upward and out of its compartment.

• Remove the battery from the midframe.

• Exercise non reuse the battery after it has been removed. The stress of removal tin can cause hidden damage to the bombardment prison cell, creating a potential safety hazard. Replace it with a new battery.

• To install a new battery:

• Remove any remaining adhesive from the phone, and clean the entire area nether the battery with isopropyl alcohol.

• Employ a few new strips of pre-cutting adhesive or Tesa tape.

• If you are attaching the battery with a custom-cut agglutinative, follow this guide.

• Press the new battery firmly into place for 5-ten seconds.

• Use a pair of tweezers to advisedly peel back the blackness safety tape securing the screen connector to the midframe.

• Utilise the flat cease of a spudger to pry upward on the screen connector to disconnect it from the motherboard.

• Apply a heated iOpener or heat gun to the screen, focusing on the left, right, and top edges of the device.

• Depending on the historic period of your phone, yous may need to apply heat for longer than usual. Be careful not to overexpose your device to directly heat, equally that can damage it.

• Apply a suction cup to the screen, as close to the heated edge at the summit of the screen every bit possible.

• Pull up on the suction cup with strong, steady strength to create a gap.

• Depending on the age of your device, this may be difficult. If y'all have trouble, apply more than heat and try again.

• Insert an opening pick into the gap.

• Leave the opening pick in the gap at the height.

• Insert another opening pick into the meridian left corner of the screen.

• Slide the pick forth the gap on the left side of the screen to piece through the adhesive securing it to the midframe.

• Leave the opening pick in the gap at the bottom left of the screen.

• Insert another opening pick into the lesser right corner of the screen.

• Slide the pick along the gap on the correct side of the screen to slice through the adhesive securing it to the midframe.

• Open up the telephone from top to lesser to ensure that the screen connector is not damaged.

• Grasp the top edge of the screen and lift it up to loosen it from the frame.

• Remove the screen from the midframe, taking care not to impairment the screen connector cable every bit you pull it through the midframe cutout.

• During reassembly, follow this guide to install custom-cutting adhesives for your device.

Squad

Embed this guide

Choose a size and copy the code beneath to embed this guide as a small widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/Motorola+Moto+G7+Power+Screen+Replacement/148017

Share this post